abeflo epoxy self-levelling flooring system for high hygiene standards

• Good protective qualities
• Self-levelling
• Chemical resistant
• Colour retention
• Wide variety of locations
• Seamless and hygienic

Precautionary Notes

(1) The substrate must be dry before application. For concrete, moisture content tests must be conducted prior to application of the priming system.

Maximum moisture content should be between 4 – 5% (preferably a Protimeter Survey Master or equivalent), or Dynamic Calcium Chloride moisture “weight gain” over 24 hours, or at least a practical overnight “plastic sheet test” is also advisable (approximately 1 m² masked down on surface).

(2) Concrete substrate must have a minimum tensile adhesion strength of 1.5 MPa and a minimum of 25 MPa compressive strength.

Concrete shall be free of all laitance and preferably should be lightly vacuum blast cleaned leaving a uniform texture.

All blemishes in the surface such as pop-outs, omegas, blowholes and honeycomb should be patched with epidermix 201. This should be left overnight to cure and shall then be rendered smooth.

For a smooth final finish, the surface profile, peak to valley, should not exceed 25% of the coating thickness. If the surface is very irregular, consideration should be given to the use of abeprime SL, a solvent free epoxy self levelling primer.

If abeprime SL is not used, then abeflo is normally applied over a thoroughly sealed concrete surface using up to two coats of abecote^® 337.

Over coating of the primer with abeflo should comply with the overcoating time requirements laid down for the specific primer. The overcoating time for abecote^® 337 is 4 – 6 hours.

Precautionary Notes

(1) When decanting base from bulk supply, thorough stirring must be accomplished beforehand.

(2) In order to avoid colour variation in large expanses, one must ensure that the same pigment batch is used and is carefully and accurately dispensed (factory batching available on request).

Proper mixing and proportioning of the epoxy binder (base and activator), filler and pigment is essential for good results with no colour variation from mix to mix.

Transfer pre-measured volume of flooring base resin to mixer.
Add pigment and activator and homogenize.

Add filler slowly and mix well.

Note:

A slow speed mixer must be used.

Ensure that the mixing vanes are below the surface of the mix to minimize air entrapment. The stirrer mixing vane configuration should be such as not to introduce unwanted aeration. Also, for this type of mixing, transferring the base/activator combination to a new container i.e. “re-mixing” will eliminate contamination due to unmixed base which is inclined to cling to the walls of the original container.

Precautionary Note

Prevailing weather conditions must be taken into account otherwise surface defects can occur (see under “properties of wet material”).

abeflo should be applied by first pouring a bead of material in the form of a ribbon on the surface to be coated. Do not leave material in the container too long because it will set faster thus reducing the work life.

Using a 5 mm serrated trowel, spread the applied material at the specified rate. Apply as evenly as is possible, working from left to right, and then back.

Approximately 10 minutes after application, roll using a porcupine roller to aid in excess air release.

All over-coating times must be strictly adhered to. abeflo will not cure if applied at below 10 °C.

abe^® super brush cleaner before setting.

Enlist the services of experienced cleaning specialists. Furthermore, the following recommendation will go a long way to maintain the original appearance of the epoxy floor viz.

(1) Protect from trafficked dirt/grit ingress into coated area by using dirt traps etc.

(2) Use of a “renewable” clear high wear polymer based floor polish will reduce scratching and “black heel”.

(3) Encourage frequent maintenance cleaning.

The epoxy floor system will be abeflo, a four-component, solvent-free epoxy floor system comprising resin and hardener, filler and pigment paste applied in accordance with a.b.e.^® recommendations.

All abeflo related products have a shelf life of 2 years if kept in a dry, cool store in the original, unopened packs.

If stored at high temperatures and/or high humidity conditions, the shelf life may be reduced.

Product safety information required for safe use is not included. Before handling, read product and safety data sheets and container labels for safe use, physical and health hazard information. The safety data sheet is available from your local a.b.e.® sales representative.

This data sheet is issued as a guide to the use of the product(s) concerned. Whilst a.b.e.^® endeavours to ensure that any advice, recommendation, specification or information is accurate and correct, the company cannot accept any liability for application – because a.b.e.^® has no direct or continuous control over where and how a.b.e.^® products are applied.

Where other products are to be used in conjunction with this material, the relevant technical data sheets should be consulted to determine total
requirements.

a.b.e.^® has a wealth of technical and practical experience built up over the years in the company’s pursuit of excellence in building and construction
technology.